Plogger Photo Feed: Sophistikits Collection

Now you can move the Middle Foundations into position. Measurements are in the instructions.

Mon, 20 Jun 2011 08:04:41 -0400

Now you can move the Middle Foundations into position. Measurements are in the instructions.

Temporary positioning of the middle Foundation pieces (not glued). Use a Center Divider as a "square" to line up the back and one edge (90 degrees). Now the glue can dry.

Mon, 20 Jun 2011 08:04:40 -0400

Temporary positioning of the middle Foundation pieces (not glued). Use a Center Divider as a "square" to line up the back and one edge (90 degrees). Now the glue can dry.

Glue and tape together these Foundation Shorts... pay attention to the way the bevels aim. Continue with the Foundation assembly without letting the glue dry.

Mon, 20 Jun 2011 08:04:40 -0400

Glue and tape together these Foundation Shorts... pay attention to the way the bevels aim. Continue with the Foundation assembly without letting the glue dry.

Two more sub-assemblies.

Mon, 20 Jun 2011 08:04:39 -0400

Two more sub-assemblies.

Organize the parts: Walls - MP walls must be painted (first coat) before any sanding, stacking, or any un-necessary handling to protect the clapboard from damage. Set everything else aside in their groups and do the first coat of painting now!

Sun, 19 Jun 2011 17:23:02 -0400

Organize the parts: Walls - MP walls must be painted (first coat) before any sanding, stacking, or any un-necessary handling to protect the clapboard from damage. Set everything else aside in their groups and do the first coat of painting now!

Organize the parts: Dividers. The Center Dividers (the two-story tall ones) will be used early in the housebody construction.

Sun, 19 Jun 2011 17:23:02 -0400

Organize the parts: Dividers. The Center Dividers (the two-story tall ones) will be used early in the housebody construction.

Organize the parts: Roofs will be a ways out in the assembly sequence... maybe they can be stored in the box.

Sun, 19 Jun 2011 17:23:01 -0400

Organize the parts: Roofs will be a ways out in the assembly sequence... maybe they can be stored in the box.

Organize the parts: Floors. You will be painting ceilings and staining floors in the pre-assembly process, so keep them handy

Sun, 19 Jun 2011 17:23:01 -0400

Organize the parts: Floors. You will be painting ceilings and staining floors in the pre-assembly process, so keep them handy

The Porch Ceiling is 1/4" thick (thinner than the Porch Floor)

Sun, 19 Jun 2011 17:23:01 -0400

The Porch Ceiling is 1/4" thick (thinner than the Porch Floor)

The Porch Floor is 3/8" thick (it is thicker than the Porch Roof)

Sun, 19 Jun 2011 17:23:01 -0400

The Porch Floor is 3/8" thick (it is thicker than the Porch Roof)

New Photograph (no caption)

Sun, 19 Jun 2011 17:23:00 -0400

New Photograph (no caption)

Sun, 19 Jun 2011 17:23:00 -0400

New Photograph (no caption)

Sun, 19 Jun 2011 17:23:00 -0400

You will be using the Foundations soon. The rest of the moldings should go into a box so they don't get lost between building sessions.

Sun, 19 Jun 2011 17:23:00 -0400

You will be using the Foundations soon. The rest of the moldings should go into a box so they don't get lost between building sessions.

Attic Partitions are 3/8" thick (thicker than the Side Roofs)

Sun, 19 Jun 2011 17:22:59 -0400

Attic Partitions are 3/8" thick (thicker than the Side Roofs)